The panel
Aim the beam at a button and pull trigger. LIBRARY, PLACE, TRANSFORM, and
DRAW all work from the same controller you are already holding. Tap the same
bar button again to close the card and stay in that mode.
LIBRARY
LIBRARY only picks a picture. There is no grab, no shoot-to-wall, and no stick
move until you open PLACE.
- WEBSITE
- On a phone or computer go to muralview2.com. Sign in, type this headset’s code to join this Quest, then upload pictures. Press REFRESH.
- HEADSET
- On your phone, open the Horizon app and put the picture in the gallery. On this headset, open Gallery, share that picture to MuralView2, then press REFRESH.
- SINGLE / STACK
- Singles stay on their own. On the website, press Select, tap the pictures, then press Stack. One picture uses Add to stack.
- REFRESH
- Pull in pictures after you upload or share.
- UNDO
- Takes the last picture down if it is the wrong one.
- Trigger a picture
- Puts it on the wall. New placement starts over. Previous placement puts it back where it was — same size, shape, and fade.
PLACE
Put the picture on a real wall, floor, or ceiling. Point at a surface and shoot
it there, then grab it to settle it, size it, and level it.
- Stick
- Slide
- Trigger at the wall
- Place
- A / X or B / Y
- Closer / farther
- Grip the picture
- Grab. Let go to drop
- Grip + stick
- Resize
- Grip + A / X
- Force vertical (tip straight up to plumb, keep left-right)
- Grip + B / Y
- Force horizontal (level)
Lock placement
Lock placement when it sits where you want it. Lock it to host a session, so
others join the print on that locked spot. Lock it for Previous, so this
picture comes back here next time.
- LOCK PLACEMENT
- Pins this picture to the wall
- UNLOCK PLACEMENT
- Lets you move it again
- HOST SESSION
- Share the locked print on Wi-Fi or a hotspot
- JOIN SESSION
- You get your own copy. Stick slides it. A / X pushes it into the wall. B / Y pulls it out. Trigger + stick fades it. The host does not see those moves.
- LEAVE
- Leave the session
DRAW
Fine-tune the picture where it sits. Slide it, scale it, spin it, fade it, and
tilt it. There is no grab and no shoot.
- Stick
- Slide
- Stick click
- Faster
- Trigger + stick up
- Dim
- Trigger + stick down
- Bring back
- Trigger + stick left / right
- Rotate
- A / X or B / Y
- Closer / farther
- Grip + stick
- Resize
- Grip + A / X
- Force vertical
- Grip + B / Y
- Force horizontal
- Grip + trigger + stick up
- Top away
- Grip + trigger + stick down
- Top toward you
- Grip + trigger + stick left
- Push left
- Grip + trigger + stick right
- Push right
TRANSFORM
Transform the picture so it fits the real surface. FREEFORM stretches it.
UNIFORM scales it evenly. DISTORT skews it. WARP pulls points on a grid.
FOLD and CURVE wrap it around walls. CORNER wraps a room corner or a column.
DOME cups a dome ceiling, or wraps the outside of a ball.
Stick slides the print. A / X undoes the last move. B / Y undoes all of it.
Stick click does not undo. Closer and farther stay in DRAW or PLACE. X leaves
a tool and brings the landing buttons back. SETTINGS holds UNDO, REDO, FLAT,
FLIP H, FLIP V, and ROTATE 45. DONE leaves TRANSFORM.
FREEFORM
Grip a corner or side to stretch. Stick slides the print. A / X undoes the last move. B / Y undoes all of it.
UNIFORM
Grip a corner to scale the whole print evenly. Stick slides it. A / X undoes the last move. B / Y undoes all of it.
DISTORT
Grip a corner to skew the print. Stick slides it. A / X undoes the last move. B / Y undoes all of it.
WARP
Grip a mesh point to warp the print. Stick slides it. A / X undoes the last move. B / Y undoes all of it.
FOLD
Trigger a line to slide it. Lines stay straight up and down, or straight across.
VERTICAL or HORIZONTAL picks the direction. Use + to add more fold seams, up to
five. Use − to take one away. Click a section — the yellow piece is the one that
folds. Then trigger + stick to fold. REVERSE flips the bend. FLAT rebuilds the
original print. A / X undoes. Stick click does not undo.
CURVE
Trigger a line to slide it. Lines stay straight up and down, or straight across.
VERTICAL or HORIZONTAL picks the direction. Use + to add more curve seams, up to
five. Use − to take one away. Click a section — the yellow piece is the one that
curves. Then trigger + stick to curve. REVERSE flips the bend. FLAT rebuilds the
original print. A / X undoes.
CORNER
IN wraps into a room corner. OUT wraps around a column. ROUND is a cylindrical
fillet. Move the line without stretching. Stick sets the angle or radius.
DOME
Trigger + stick up cups a dome ceiling. Stick down wraps a ball. UNDO goes back
a step. FLAT rebuilds the original print.
Shared Vision
Lock the print, then tap HOST SESSION. Others on the same Wi-Fi or hotspot tap
JOIN SESSION. The picture, size, angle, placement, fade, and shape start the same.
After that, each headset keeps its own copy. Hosted pictures and joined pictures
go into Shared Vision in LIBRARY, marked HOSTED or JOINED. Later you can tap one
and use Previous placement. JOINED stays on join tools: slide, in or out, and fade.
- Host
- You will not see the other person’s copy move or fade
- Join
- Your own copy. Stick slides it. A / X in. B / Y out. Trigger + stick fades. No resize and no flip
